5.0 Acoustic

Table 5.1 provides acoustic performance levels for PowerBlock walls. For alternatives and composite wall construction, Table 3.2 are acoustic performance for PowerBlock systems.

Table 5.1:  Acoustic Performance

PowerBlock Thickness Rw Rw+ Ctr
100 38 35
150 43 40
200 45 42

Values for PowerBlock only, no linings.

find out more

8.0 System Components

Products

Hebel stocks many of the products and materials required to construct your Hebel home.

Product Description Product Description
  Hebel Thermoblocks

50mm – 300mm (25mm
increments)

  Hebel Adhesive
20 kg bag

Used for gluing the blocks together at vertical and horizontal joints

  Sill blocks

600x200x50mm thick or
100mm thick, 30º slope

  PowerFloor Panels

1800mm x 600mm x 75mm

  Hebel Mortar
20 kg bag

Used as thick bed mortar base
to provide a level base for the
first course

  Custom PowerFloor Panels

150mm – 250mm x 600mm
by up to 6m

  Hebel Lintels

To suit openings up to 5m

  Hebel HighBuild render 20kg bag

Used as a preparation coat
to level surface providing an
even true surface

  Stair treads

300mm x 175mm x 1m
or 1.2m

  Control joint tie

Used at every third
course in control joints

  Hebel Patch
10kg bag

Used to prepare minor chips
or damage to blocks

  Sliding joint tie

Fixed to RHS/SHS column
every second course

  Corrosion Protection Paint

To coat exposed
reinforcement during cutting

find out more

 

10.0 Tools & Equipment for Construction

Hebel PowerBlocks can be laid using construction tools/equipment.

String Line – A string line is required to accurately set out and lay Hebel PowerBlock Walls.

Brick/Blocklaying Profiles – used to gauge the block course are being laid level.

Mixing Bucket – a minimum 20 litre bucket is required for mixing Hebel Mortar, Hebel Adhesive and Hebel HighBuild render.

Electric Drill – an electric drill is required to mix the Hebel Mortar, Hebel Adhesive and Hebel HighBuild render. It is also used to drill clearance holes in the blocks so they can be placed over the tied down rods where required.

Stirrer – fitted to the electric drill, the stirrer is used to mix the Hebel Mortar, Hebel Adhesive and Hebel HighBuild render inside the mixing bucket.

Notched Trowel – the notched trowel is used to apply the Hebel Adhesive to the Hebel surfaces. The width of the trowel must match the block thickness to ensure the adhesive is applied with full and even coverage.

Rubber Mallet – a rubber mallet is required to ‘tap’ the Hebel PowerBlocks onto the adhesive and into place.

Spirit Level – required to install the blocks level and plumb.

Hand Saw – a Hebel handsaw can be used to cut Hebel PowerBlocks to length and height.

Powered Bandsaw – a bandsaw is ideal for cutting Hebel PowerBlocks. (perfect when there are many site cuts to be performed).

Hebel Square – a purpose built square is available for use when marking and cutting Hebel PowerBlocks.

Steel, Plastic and Timber Trowels – these trowels may be required for the installation of the Highbuild render and texture coatings.

Sanding Float – used to even out inconsistencies in the Hebel PowerBlock Wall in preparation for render/texture coats.

Hebel Hand Router – may be used to chase services into solid Hebel walls.

Circular Saw – (fitted with a diamond blade) may be used to chase services into solid Hebel walls.

Electric Router – may be used to chase services into solid Hebel walls.

Crane – may be required to lift large Hebel Lintels and Hebel custom floor panels.

Lifting Grabs – required for use in conjunction with crane for lifting Hebel lintels and custom floor panels.

Scaffold – Scaffold is required when building block walls. The amount of scaffold depends on the height of the walls.

Sealant Gun – required to fill the control joints in the Hebel PowerBlock Walls.

Image 10.1:  Hebel® tools

find out more

Appendix A – Carpet Installation

Panel Surface Preparation

Sweep the floor surface to remove debris and loose particles. Expose all surface blemishes such as chips, cracks, gaps, ridges or the like. Fill all unacceptable locations with an appropriate and compatible patching compound such as Hebel Patch or levelling compound as required. Ensure panels are then dry.

Carpet Smooth Edge Installation

Installation of Carpet Smooth Edge (Gripper) is to be in accordance with AS/NZS 2455.1:1995.

Installation of carpet gripper prior to laying carpet requires the use of specifically selected nails or course threaded screws. Standard fixings supplied with the carpet gripper are not suitable for fixing to Hebel PowerFloor panels. Carpet gripper strips are available without factory supplied nails. For carpet gripper installation near the panel edge, only glue is recommended. If relying on glue only, the carpet can not be stretched until the glue is set after approximately 24 hours.

Table A.1 – Carpet Smooth Edge Fixings
Fixing Type Description Application
Method
Installation Notes
Twist Nails 51mm domehead twist nail Coil Nail Gun(Refer to Fig A.1) The head of the twist nailshould finish flush with
the surface of the gripper
strip
Screws Type 17 point- course thread
No. 8g x 50mm
– Countersinking
screw
Makita 6834Auto Feed
Screwdriver
(Refer to Fig A.2)
The head of the twist nailshould finish flush with
the surface of the carpet
gripper strip
Screws Type 17 pointTrimhead deckScrew.
4.2 x 50mm
4.2 x 65mm
Quickdrive auto feed The head of the screwshould be flush with the
smooth edge

Underlay Installation

Minimum medium duty underlay is to be used. No other special requirements.

Carpet Installation

As per carpet manufacturer’s guidelines. No other special requirements.

find out more